NE4-T General Analogue Baths
NE4-T General Stirred Analogue Baths
Clifton stirred analogue water baths are designed for immersion of flasks, bottles and racks in a stable temperature environment.
The stainless steel tank is contained within a sturdy outer case and supplied complete with a stainless steel shelf, which provides good water circulation and temperature stability.
See the range of accessories compatible with the NE4-T range.
3 Year Warranty
The NE4-T Series comes with a 3 year warranty as standard, we also offer free advice and support for our baths.
MADE IN GREAT BRITAIN
The NE4-T Series is made here in Great Britain with the highest quality of materials.
Clifton stirred water baths are designed for immersion of flasks, bottles and racks in an accurate temperature environment throughout the water bath.
3 Year Warranty.
Before leaving our factory every water bath is identified with a unique serial number and undergoes a factory calibration adjusting control to known traceable value. Electrically tested for safety at final inspection and a test certificate enclosed in rear of the instruction book.
Broad range of accessories available to suit wide range of applications.
Painted surfaces feature “anti-bacterial technology” which inhibits bacterial growth, improving hygiene requirements as demanded by clinical and laboratory environments.
- The bath features a low liquid level float switch. This ensures heating will be switched off if the liquid level falls below the recommended level. The motor and heater are switched off in this instance.
Energy Consumption
0.5kWh @ 37°C
0.4kWh @ 60°C - lid fitted
(Based on NE4-8T)
The lower the figure, the less energy used. Information supplied for size and range comparison, guidance only and measured consumption at set point. Please remember that the energy consumption may vary due to factors such as location, ventilation, ambient temperatures and loading.
Controls
Thermostatic temperature control, providing quick reliable selection and attainment of desired operating temperature. Every unit undergoes a factory calibration at 50°C for validation.
Heating Information
For water temperatures above 60°C we recommend that an accessory lid or layer of spheres are used for optimum performance. This will reduce evaporation and a lid will keep the samples and water free from contamination. Optimum performance saves energy by reducing electricity consumption and running costs.
Stainless Steel Gable Lid
Clifton stainless steel gable lids help reduce evaporation, assist in keeping samples in a water bath free from contamination and save energy. These stainless steel gable lids with a high profile allow extended use of the bath, right into the edges of the tank. No drip points to contaminate samples whilst the lid design ensures all condensate returns back into the bath. Insulated handles for safe use.
|
Product Code |
Bath |
|---|---|
|
SL4-8 |
NE4-8T |
|
SL4-14 |
NE4-14T |
|
SL4-22 |
NE4-22T NE4-28T |
Stainless Steel Flat Lid
LD4 series lid, completely manufactured from bright polished stainless steel with a large insulated lifting handle. Above 60°C or below room temperature it is recommended that to achieve optimum performance the bath should be covered with a lid.
|
Product Code |
Bath |
|---|---|
|
LD4-8 |
NE4-8T |
|
LD4-14 |
NE4-14T |
|
LD4-22 |
NE4-22T NE4-28T |
Stainless Steel Test Tube Racks
Laboratory test tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
- NE4-8T = 1 rack
- NE4-14T = 3 racks
- NE4-22T = 5 racks
- NE4-28T = 5 racks
| Product Code |
|---|
|
6870 - (26 holes x 17mm diameter) |
|
6871 - (16 holes x 26 mm diameter) |
|
6872 - (36 holes x 13mm diameter) |
|
6873 - (18 holes x 19mm diameter) |
|
6900 - (12 holes x 32mm diameter) |
Stainless Steel Raised Shelves
|
Product Code |
Bath |
|---|---|
|
RS4-14 |
NE4-14T NE4-22T NE4-28T |
|
RS4-22 |
NE4-22T NE4-28T |
Drain Tap
Water baths with serial numbers greater than 75100 should order this accessory drain tap BX0953. These fast draining outlets means it only takes 13 minutes to empty a 28 litre bath.
|
Product Code |
Bath |
|---|---|
|
BX0953 |
NE4-28T |
Hose Tail Nozzle
The hose tail nozzle attaches to the tap to allow connection for 12mm i.d rubber hose.
| Product Code | Bath |
|---|---|
|
BX0952 |
NE4-28T |
UNIVERSAL ACCESSORIES
This blanket of hollow spheres is ideal for open tanks of water. Reduces thermal losses – Savings of up to 70% can be achieved with a single layer – Increase energy saving & reducing costs.
| Product Code |
Capacity |
| BP0368 : 1 Pack |
8 Litre baths |
| BP0368 : 2 Pack |
14 Litre baths |
| BP0368 : 3 Packs |
22 Litre baths
28 Litre baths |
Allows easy and quick emptying of water baths, immerse into water bath, squeeze the bellow and point the outlet to a bucket or sink.
| Notes : |
Water temperature must be below 45°C before use. |
| Product Code : |
BX0616 |
Factory Calibration record must be ordered with equipment.
Notes
1. Factory calibration record. 2. The completed calibration record will be enclosed at the rear of the instruction book accompanying the Clifton unit carrying the following information: Unique record number for traceability. 3. The measurement of uncertainty ±0.8°C. Ambient temperature 21°C ±3°C. Notes: A. The calibration record provides a measurement of precision about set point with maximum and minimum sensitivity readings obtained. Precision is defined as “(1) The ability of a measurement to be consistently reproduced” and “(2) The number of significant digits to which a value has been reliably measured”. B. The calibration record does not provide or assures any form of accuracy. Accuracy is defined as “the ability of a measurement to match the actual value of the quantity being measured”. |
Product Code : CAL
Downloads
The water bath brochure contains all the information on our Clifton water baths, including the shaking baths and the ultrasonic baths.
Detailed document containing the specifications for the NE4-T range of baths.